A research about bending strain effect on splice characteristics in YBa2 Cu3 O7 coated conductors under various pressures in splicing

Hyung Jun Kim, Ki Sung Chang, Young Jae Kim, Hyun Chul Jo, Kyoung Jun Kim, Haigun Lee, Tae Kuk Ko

Research output: Contribution to journalArticle

4 Citations (Scopus)

Abstract

A magnet using a High-Tc Superconducting (HTS) tapes often consist of stacked pancakes or solenoids. Need for connecting each coil or adding insufficient superconducting part of applications is the reason why splice is required. Splice characteristics on the tapes wound on curved area are easily subjected to bending force. In order for the tape on the curved area to achieve appropriate splice characteristics, the effect of both applied pressure and bending strain should be taken into consideration. In this paper both bending strain and pressure dependent splice characteristics were investigated to figure out design parameters of magnet applications, which include the curved area in splicing. A tape was firstly spliced on a flat plate, and then the tape made curved. The splice and curve were performed under various conditions in terms of pressure and strain. Characteristics of spliced samples such as splice resistance and critical current were measured from V-I curves. We also drew the preferred splice condition through experimental results.

Original languageEnglish
Article number5675717
Pages (from-to)3001-3004
Number of pages4
JournalIEEE Transactions on Applied Superconductivity
Volume21
Issue number3 PART 3
DOIs
Publication statusPublished - 2011 Jun 1

Fingerprint

splicing
Tapes
tapes
conductors
Magnets
Superconducting tapes
magnets
Critical currents
Solenoids
curves
flat plates
solenoids
critical current
coils

Keywords

  • Coated conductor
  • Critical current
  • Curvature
  • Lap joint
  • Splice resistance

ASJC Scopus subject areas

  • Electrical and Electronic Engineering
  • Condensed Matter Physics
  • Electronic, Optical and Magnetic Materials

Cite this

A research about bending strain effect on splice characteristics in YBa2 Cu3 O7 coated conductors under various pressures in splicing. / Kim, Hyung Jun; Chang, Ki Sung; Kim, Young Jae; Jo, Hyun Chul; Kim, Kyoung Jun; Lee, Haigun; Ko, Tae Kuk.

In: IEEE Transactions on Applied Superconductivity, Vol. 21, No. 3 PART 3, 5675717, 01.06.2011, p. 3001-3004.

Research output: Contribution to journalArticle

Kim, Hyung Jun ; Chang, Ki Sung ; Kim, Young Jae ; Jo, Hyun Chul ; Kim, Kyoung Jun ; Lee, Haigun ; Ko, Tae Kuk. / A research about bending strain effect on splice characteristics in YBa2 Cu3 O7 coated conductors under various pressures in splicing. In: IEEE Transactions on Applied Superconductivity. 2011 ; Vol. 21, No. 3 PART 3. pp. 3001-3004.
@article{eb1bb0bd608149108632dc8f139586f9,
title = "A research about bending strain effect on splice characteristics in YBa2 Cu3 O7 coated conductors under various pressures in splicing",
abstract = "A magnet using a High-Tc Superconducting (HTS) tapes often consist of stacked pancakes or solenoids. Need for connecting each coil or adding insufficient superconducting part of applications is the reason why splice is required. Splice characteristics on the tapes wound on curved area are easily subjected to bending force. In order for the tape on the curved area to achieve appropriate splice characteristics, the effect of both applied pressure and bending strain should be taken into consideration. In this paper both bending strain and pressure dependent splice characteristics were investigated to figure out design parameters of magnet applications, which include the curved area in splicing. A tape was firstly spliced on a flat plate, and then the tape made curved. The splice and curve were performed under various conditions in terms of pressure and strain. Characteristics of spliced samples such as splice resistance and critical current were measured from V-I curves. We also drew the preferred splice condition through experimental results.",
keywords = "Coated conductor, Critical current, Curvature, Lap joint, Splice resistance",
author = "Kim, {Hyung Jun} and Chang, {Ki Sung} and Kim, {Young Jae} and Jo, {Hyun Chul} and Kim, {Kyoung Jun} and Haigun Lee and Ko, {Tae Kuk}",
year = "2011",
month = "6",
day = "1",
doi = "10.1109/TASC.2010.2093098",
language = "English",
volume = "21",
pages = "3001--3004",
journal = "IEEE Transactions on Applied Superconductivity",
issn = "1051-8223",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "3 PART 3",

}

TY - JOUR

T1 - A research about bending strain effect on splice characteristics in YBa2 Cu3 O7 coated conductors under various pressures in splicing

AU - Kim, Hyung Jun

AU - Chang, Ki Sung

AU - Kim, Young Jae

AU - Jo, Hyun Chul

AU - Kim, Kyoung Jun

AU - Lee, Haigun

AU - Ko, Tae Kuk

PY - 2011/6/1

Y1 - 2011/6/1

N2 - A magnet using a High-Tc Superconducting (HTS) tapes often consist of stacked pancakes or solenoids. Need for connecting each coil or adding insufficient superconducting part of applications is the reason why splice is required. Splice characteristics on the tapes wound on curved area are easily subjected to bending force. In order for the tape on the curved area to achieve appropriate splice characteristics, the effect of both applied pressure and bending strain should be taken into consideration. In this paper both bending strain and pressure dependent splice characteristics were investigated to figure out design parameters of magnet applications, which include the curved area in splicing. A tape was firstly spliced on a flat plate, and then the tape made curved. The splice and curve were performed under various conditions in terms of pressure and strain. Characteristics of spliced samples such as splice resistance and critical current were measured from V-I curves. We also drew the preferred splice condition through experimental results.

AB - A magnet using a High-Tc Superconducting (HTS) tapes often consist of stacked pancakes or solenoids. Need for connecting each coil or adding insufficient superconducting part of applications is the reason why splice is required. Splice characteristics on the tapes wound on curved area are easily subjected to bending force. In order for the tape on the curved area to achieve appropriate splice characteristics, the effect of both applied pressure and bending strain should be taken into consideration. In this paper both bending strain and pressure dependent splice characteristics were investigated to figure out design parameters of magnet applications, which include the curved area in splicing. A tape was firstly spliced on a flat plate, and then the tape made curved. The splice and curve were performed under various conditions in terms of pressure and strain. Characteristics of spliced samples such as splice resistance and critical current were measured from V-I curves. We also drew the preferred splice condition through experimental results.

KW - Coated conductor

KW - Critical current

KW - Curvature

KW - Lap joint

KW - Splice resistance

UR - http://www.scopus.com/inward/record.url?scp=79957936988&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=79957936988&partnerID=8YFLogxK

U2 - 10.1109/TASC.2010.2093098

DO - 10.1109/TASC.2010.2093098

M3 - Article

VL - 21

SP - 3001

EP - 3004

JO - IEEE Transactions on Applied Superconductivity

JF - IEEE Transactions on Applied Superconductivity

SN - 1051-8223

IS - 3 PART 3

M1 - 5675717

ER -