Study on the deburring of intersecting holes with abrasive flow machining

Joon Kyu Beom, Young Gwan Kim, Kwang Joon Kim, Kwon Hee Kim

Research output: Contribution to journalArticle

Abstract

Intersecting holes deep inside a workpiece, are difficult to deburr because of poor accessibility. When holes are small and the intersecting angle (acute angle between hole axes) is less than 45 o , difficulty is at its extreme. In this study, abrasive flow machining is used for a hole diameter of 3mm and intersecting angles of 30o and 45 o . Tests were performed for AL6061 specimens, with process parameters allocated to L8(2 7 ) orthogonal array. Degree of deburring is strongly dependent on intersecting angle, abrasive grit size, and total volume of flow. Successful deburring was achieved for 30 intersecting angle.

Original languageEnglish
Pages (from-to)163-168
Number of pages6
JournalJournal of the Korean Society for Precision Engineering
Volume36
Issue number2
DOIs
Publication statusPublished - 2019 Feb 1

Fingerprint

Deburring
Abrasives
Machining

Keywords

  • Abrasive flow machining
  • Burr
  • Deburring
  • Intersecting holes

ASJC Scopus subject areas

  • Safety, Risk, Reliability and Quality
  • Mechanical Engineering
  • Industrial and Manufacturing Engineering

Cite this

Study on the deburring of intersecting holes with abrasive flow machining. / Beom, Joon Kyu; Kim, Young Gwan; Kim, Kwang Joon; Kim, Kwon Hee.

In: Journal of the Korean Society for Precision Engineering, Vol. 36, No. 2, 01.02.2019, p. 163-168.

Research output: Contribution to journalArticle

Beom, Joon Kyu ; Kim, Young Gwan ; Kim, Kwang Joon ; Kim, Kwon Hee. / Study on the deburring of intersecting holes with abrasive flow machining. In: Journal of the Korean Society for Precision Engineering. 2019 ; Vol. 36, No. 2. pp. 163-168.
@article{257bf27fb9734d06b1353bcf6415f7b9,
title = "Study on the deburring of intersecting holes with abrasive flow machining",
abstract = "Intersecting holes deep inside a workpiece, are difficult to deburr because of poor accessibility. When holes are small and the intersecting angle (acute angle between hole axes) is less than 45 o , difficulty is at its extreme. In this study, abrasive flow machining is used for a hole diameter of 3mm and intersecting angles of 30o and 45 o . Tests were performed for AL6061 specimens, with process parameters allocated to L8(2 7 ) orthogonal array. Degree of deburring is strongly dependent on intersecting angle, abrasive grit size, and total volume of flow. Successful deburring was achieved for 30 intersecting angle.",
keywords = "Abrasive flow machining, Burr, Deburring, Intersecting holes",
author = "Beom, {Joon Kyu} and Kim, {Young Gwan} and Kim, {Kwang Joon} and Kim, {Kwon Hee}",
year = "2019",
month = "2",
day = "1",
doi = "10.7736/KSPE.2019.36.2.163",
language = "English",
volume = "36",
pages = "163--168",
journal = "Journal of the Korean Society for Precision Engineering",
issn = "1225-9071",
publisher = "Korean Society for Precision Engineeing",
number = "2",

}

TY - JOUR

T1 - Study on the deburring of intersecting holes with abrasive flow machining

AU - Beom, Joon Kyu

AU - Kim, Young Gwan

AU - Kim, Kwang Joon

AU - Kim, Kwon Hee

PY - 2019/2/1

Y1 - 2019/2/1

N2 - Intersecting holes deep inside a workpiece, are difficult to deburr because of poor accessibility. When holes are small and the intersecting angle (acute angle between hole axes) is less than 45 o , difficulty is at its extreme. In this study, abrasive flow machining is used for a hole diameter of 3mm and intersecting angles of 30o and 45 o . Tests were performed for AL6061 specimens, with process parameters allocated to L8(2 7 ) orthogonal array. Degree of deburring is strongly dependent on intersecting angle, abrasive grit size, and total volume of flow. Successful deburring was achieved for 30 intersecting angle.

AB - Intersecting holes deep inside a workpiece, are difficult to deburr because of poor accessibility. When holes are small and the intersecting angle (acute angle between hole axes) is less than 45 o , difficulty is at its extreme. In this study, abrasive flow machining is used for a hole diameter of 3mm and intersecting angles of 30o and 45 o . Tests were performed for AL6061 specimens, with process parameters allocated to L8(2 7 ) orthogonal array. Degree of deburring is strongly dependent on intersecting angle, abrasive grit size, and total volume of flow. Successful deburring was achieved for 30 intersecting angle.

KW - Abrasive flow machining

KW - Burr

KW - Deburring

KW - Intersecting holes

UR - http://www.scopus.com/inward/record.url?scp=85061331263&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85061331263&partnerID=8YFLogxK

U2 - 10.7736/KSPE.2019.36.2.163

DO - 10.7736/KSPE.2019.36.2.163

M3 - Article

VL - 36

SP - 163

EP - 168

JO - Journal of the Korean Society for Precision Engineering

JF - Journal of the Korean Society for Precision Engineering

SN - 1225-9071

IS - 2

ER -